Now run the ice maker for at least 3 cycles, so that lemon juice removes any dirt or scale from the parts. Throw all the ice cubes made in this process. Now drain the excess water and wash the reservoir. You can use a soft cloth to wipe the ice maker rods and water reservoir. Do not forget to remove the plug from the power source. Once again, fill the reservoir with fresh water. Run for at least cycles and throw the ice cubes made during this. Note — If your ice maker starts making cloudy ice, you can repeat the same process after months.
You can read my ice cleaning guide for more details. Generally, the company claims no installation is required for countertop ice makers. I have explained the complete process to install a new countertop ice maker for the first time. Save my name, email, and website in this browser for the next time I comment. Check this - 1. Why does my ice maker make a knocking sound 2. Some of the tools needed include an adjustable wrench, drill, flat-head screwdriver, Philips-head screwdriver, paddle bit.
Next step after installing the valve is to mount the first part of the ice maker kit known as the solenoid valve. This article contains a step-by-step guide on how to install an ice maker to a refrigerator alongside a solenoid valve that automatically brings water to the ice machine The materials that you would need include icemaker kits, isolation valves, water supply installation kits, threaded brass fitting, and nipples.
Run the water line Make a hole behind the refrigerator and another under the sink. Toll the waterline down and run it through the refrigerator hole. Drain the Water Line Shut off the water to the house at its main source and shut off the electric heater at the breaker. Tap into the cold water underneath the sink By opening a faucet, drain the lines. Things You'll Need. Related Articles.
Method 1. All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc. Locate the closest cold water source. To install an ice maker you will have to tap into the closest-located cold water pipe.
Find this cold water source, which may be found under a sink, below the floor, or in a wall. If you need to drill through the floor or wall to reach the pipe, it is best to hire a professional who will know how to avoid wires, ducts, or other plumbing.
You will need to install a cold water line for either a refrigerator ice maker or an under-counter ice maker. Shut off the water and drain the pipe. Turn off the main water valve before starting your project by turning it clockwise. This valve will likely be located on a perimeter wall of your home, in your basement, or near an outdoor water meter.
Open the cold water faucet to let water drain out of the pipe. Attach a saddle valve to a clean spot on the cold water pipe. A saddle valve is a valve that hugs a water line on both sides and supplies a low pressure stream from it.
Wipe the area of your cold water pipe that you will attach the valve onto with a clean, wet cloth. Place a saddle valve onto the pipe and tighten its clamps so that it grips the pipe.
You can purchase a saddle valve at any hardware store. Screw the valve in to pierce a hole in the pipe. Slowly turn the handle of the valve in a clockwise direction. When you meet resistance, keep turning the valve firmly.
Continue until the needle pierces through the pipe. You will feel less resistance once the needle pierces through the pipe. Attach 0. Place 1 end of your copper tubing into the valve opening. Screw on a small compression joint to secure the connection. Measure the distance between your ice maker and the cold water pipe before purchasing the copper tubing to get the appropriate length. Turn the water back on. Once you have attached the saddle valve and copper piping, you can turn your water back on.
First, make sure all of your connections are secure. Turn the main water valve counterclockwise to turn the water back on. Open the saddle valve to rinse through the copper piping into a large bucket. Gently turn the handle on your saddle valve counter-clockwise to open the valve. Direct the end of your copper tubing unto a large bucket.
Let enough water flow through to fill the bucket, then close the valve. Method 2. Locate the ice maker on your refrigerator.
0コメント