Video Channel Setting. Automatic Tuning. Normal Playback. Normal Recording. Basic Playback. Step by Step Playback. We recommend always to use the standardized, properly formatted discs.
Please contact your Hitachi dealer for more detail. If you cannot play back a disc which bears one of the marks above, check the following notes. Discs unfinalized or recorded in the video recording format cannot be played back. Depending on the recording status of a disc, the disc may not be played back at all or normally the picture or sound may be not be smooth, etc. If you use nonstandardized discs, this unit may not play them back. Even if they are played back, the sound or video quality will be compromised.
Otherwise, malfunction may result! The sound recorded on the high density Super Audio CD layer cannot be delivered. When the screen saver program is activated for 30 minutes, the power is automatically turned off.
Information about the current operation can be displayed on the TV screen, allowing you to confirm the currently active functions such as program playback by the remote control. Manufactured under license from Dolby Laboratories.
Press DVD on the remote control. Press VCR on the remote control. You always need to select the correct mode on the remote control too. Connect a video cable coming from the video out jack of a camcorder, another VCR, or a video source laser disc player, camcorder, etc.
Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here. Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode Rewind Search. Press to rapidly advance the tape, or view the picture rapidly in forward during playback. Forward Search.
Press once to start a recording. Press repeatedly to start a One Touch Recording. Display, Remote Sensor Window. In VCR mode, press to change TV programmes on the VCR; press to adjust the tracking during normal or slow motion playback; press to remove vertical jitter in a Still picture. This light appears when the VCR output mode is selected. However, if you press. This light appears when the DVD output mode is selected.
When a chapter or track is switched, the number of a new title, chapter or track is displayed. Replace it with a new battery as soon as possible. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Instruction manual To obtain the best performance and ensure years of troublefree use, please read this instruction manual completely.
Caution 1 Do not attempt to open the cabinet. If liquid is spilled into the unit, consult qualified service engineer. Mains Cord This appliance may be fitted with a non-rewireable plug. Important As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase Dealer Phone No. Dealer Purchase from Model No. Dealer Address Serial No. Parts identified by the! Replace only with part number specified.
In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise block- ing capacitors, and noise blocking filters, etc. Use specified internal wiring. Use specified insulating materials for hazardous live parts.
When replacing AC primary side components transformers, power cord, etc. Observe that the wires do not contact heat produc- ing parts heatsinks, oxide metal film resistors, fus- ible resistors, etc. Check that replaced wires do not contact sharp edges or pointed parts. When a power cord has been replaced, check that 5 - 6 kg of force in any direction will not loosen it.
Also check areas surrounding repaired locations. Be careful that foreign objects screws, solder droplets, etc. Crimp type wire connector The power transformer uses crimp type connec- tors which connect the power cord and the primary side of the transformer. When replacing the trans- former, follow these steps carefully and precisely to prevent shock hazards.
Replacement procedure 1 Remove the old connector by cutting the wires at a point close to the connector. Important: Do not re-use a connector. Discard it.
If the wires are stranded, twist the strands to avoid frayed conductors. Insert the wires fully into the connector. Be sure to crimp fully to the complete closure of the tool. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC outlet. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and con- firm the specified values to verify compliance with safety standards.
Clearance Distance When replacing primary circuit components, confirm specified clearance distance d and d' between sol- dered terminals, and between terminals and sur- rounding metallic parts. See Fig. Be sure to confirm the precise values. Leakage Current Test Confirm the specified or lower leakage current between B earth ground, power cord plug prongs and externally exposed accessible parts RF termi- nals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.
Use an AC voltmeter to measure across the terminals of load Z. Connected in parallel i 0. Alignment of Tape Path. Schematic Diagrams. Schematic Diagram. S Jack-A Schematic Diagram.
S IC Voltage Chart. S Waveforms. B-2 Video Block Diagram. B-3 Audio Block Diagram. B-5 Power Supply Block Diagram. This DVD player uses a pickup that emits a laser beam.
When checking the laser diode, be sure to. Do not look directly at the. Caution: Use of controls and adjustments, or doing procedures other than those specified herein, may result in. Do not look directly at the laser beam coming.
0コメント